How to make earrings with superduo beads - step by step diamond earrings

We cut about 1.5m thread and thread it on the needle. We thread one TOHO bead and tie a thread about 10 cm from the end of the thread. He will be our stopwatch.

We thread 3 S1 beads by pulling the thread through one hole from each bead.

We pass the needle through the second hole of the last bead, turning the thread.

Aligning the beads in a visible way in the picture we thread the S2 bead.

We thread the thread through the upper hole of the first bead S1.

When working, make sure that the beads adhere nicely to each other, but do not stretch the thread too much because it can cause the earring to wave.

We thread another S1 bead ...

... and then put the thread through the second hole of the same bead and turn the thread back.

We thread the S2 bead.

We thread the thread through the upper hole of the S2 bead in the middle of the work.

We thread one S2 bead and one S1 bead and set the strung beads visible in the photo - S2 bead up and S1 bead down.

We can already see how the pattern is created from the bottom of the bead.

We pull the needle through the second hole of the last S1 bead and all the holes of the beads on the same level (a total of 5 beads).

We pull the needle through the second hole of the last S1 bead and all the holes of the beads on the same level (a total of 5 beads).

We thread the S1 bead.

We thread the thread through the second hole of the last S1 bead, turning the thread.

We thread the S2 bead.

We thread the thread through the S2 bead in the earring.

We thread the S1 bead.

We thread the thread through the S2 bead at work.

We thread the beads S2 and S1 and set them as shown in the photo - S2 up and S1 down.

We thread the thread through the second hole of the last S1 bead and then all the holes in the beads in the same row.

We pass the needle through the second hole of the last S1 bead and all the holes in the beads in this row.

We proceed in the same way creating the next 3 rows.

We proceed in the same way creating the next 3 rows.

Passing through the thread through all the beads in the seventh row, we do not pass through the last bead S1. From now on we will narrow our earring.

We go through the second hole in the last bead S2.

We make the beads in a row in the same way as before (two S1 beads, one S2 bead, two S1 beads).

We pass the needle through the second hole of the last bead S2 (lower row) ...

and subsequent beads in the same row ending with the last S2 bead (We do not go through the S1 bead).

We turn the thread in the S2 bead again.

We go through the holes of all beads to S1 ending.

We thread the thread through the second hole in the last bead S1.

We complete the next row with four S1 beads and go through the last S1 bead in the earring.

Again, pull the thread in a row below and in the same way narrow the earring to the last bead.

After sewing the entire earring, we thread the thread inside and tie a double knot.

We hide the thread passing again through several beads inside the earring and cut it.

We remove our stopper from the end of the earring and thread the thread. As from the previous page, we go to the center of the earring, tie a double knot and hide the thread.

Using pliers, we bend the assembly ring and put it through the last bead in the earring.

We put the earring hook on the ring and clamp it with pliers.

The earring is ready. It's enough to create a second one in the same way and you can enjoy your new acquisition.

We hope you liked Julita's SuperDuo earings. We would love to see your versions, feel free to share them with our Facebook group.