Golden Christmas Kumihimo Bracelet | beadsdirect.co.uk
0

Golden Christmas Kumihimo Bracelet

Products used in project:

Golden Christmas Kumihimo Bracelet

Items (9)
Qty
Price
Fevi Kwik One Drop Instant Adhesive/Glue 1g Tube
W311
1
Out of stock
S-Lon Bead Cord 77yrds (70m) Cream
TC370
1
Out of stock
"X" Miyuki Long Magatama 4x7mm Duracoat Galvanised Shiny Gold 10g
LMA4202
2
Out of stock
Miyuki Long Magatama 4x7mm Crystal Transparent Silver Lined 10g
LMA0001
2
Out of stock
No Tangle Thread Bobbins (2 1/2 Inch dia 3/8 hole) Pk8
W510
1
Out of stock
Silver Plated Lobster Clasps 7x14mm Pk5
F0300
1
Out of stock
Silver Plated Iron Jumprings 4mm 0.8mm Thick Pk100
F0210
1
Out of stock
X-Beads Direct Kumihimo Small Round Disk 4.25 Inch Pk1
W343
1
Out of stock
Total Cost
£1.19

Not all products are available for this project

Information about project:

Golden Christmas Kumihimo Bracelet

Designed by: Holly Eve

Difficulty: Beginner

Rating:

Learn how to create sparkling Kumihimo designs with your favourite magatama beads!
For this project you will need a Kumihimo braiding disk and some no-tangle bobbins. These are included in your materials list!

Step 1

Cut 4 strands of s-lon cord approx. 6 times the length you'd like your finished bracelet to measure. Holding all 4 cords together, fold in the middle of the cords and knot together creating 8 ends. Place the knot through the hole in the centre of the braiding board. Spread the cords, placing one strand either side of each dot on the board.

Step 2

Thread 30 long magatama beads on to each strand, each bead must face the same direction so you must always thread up through the hole consistently. Thread one colour onto 4 cords and the second colour onto the remaining 4 cords. Turn the braiding board over and wrap each cord into its own no-tangle bobbin. You may want to add a weight to the knot to help your braid pull downwards as you work.

Step 3

Position the cords - put the 2 gold beaded cords on the left and right side of your board on either side of the dots. Position the silver/clear beaded cords at the top and bottom positions on the board.

Step 4

You should have a cord either side of dot 32. Rotate the board so you are holding this dot at the top. Take the cord from the notch to the left of dot 16 (at the bottom) and move it straight upwards to the notch to the left of the two cords at the top. You will now have 3 cords at the top and one at the bottom. Now take the cord furthest right at the top and bring it down to the right of the remaining bottom cord. Turn the braiding board 90 degrees counter-clockwise and repeat the same process, moving the bottom left cord to the top left, and the top right cord to the bottom right. Repeat until you have created a few centimetres of unbeaded braid.

Step 5

Now bring a bead down the next cord you work with. Place it all the way to the bottom of the cord. You will find that it sits under the cord you used last. Make sure the longer part of the bead points outwards. Repeat this every time you move a cord until you have used all the beads you added earlier. You can use more or less beads if you want to change the size of the bracelet. Create a few more centimetres of unbeaded braid.

Step 6

Remove cords from the notches and knot together so the braid doesn’t unravel. Now wrap some cotton or thread tightly around the braid just below the knot, and sew through the braid a couple of times to make sure it is securely fastened. When you are happy that you have secured the braid; take some sharp scissors and cut off the knot.

Step 7

To complete, check that the end of your cord fits into your cord ends. Glue each end into the clasp using fevi kwik, and leave to dry.
Attach your lobster clasp to each of your cord ends using jumprings.