Become a VIBGOLD Member today and receive FREE UK DELIVERY and 30% off your next order 

30% Off Glass Beads, Ends Midnight Friday  

Beads Direct - Beads for jewellery making, beads for craft and beadwork, semi-precious gemstones, glass beads, Swarovski Crystallized Elements, seed beads, silver beads, jewellery findings and more 0

Basket Summary

0

Blue and White Shamballa Fashion Bracelet

Blue and White Shamballa Fashion Bracelet

Blue and White Shamballa Fashion Bracelet

Products used in the project

Item QTY Price

Waxed Nylon Cord 1.5mm x 9m Black

TC376

1 £1.48

Onyx Matte Black 6mm Round Pack 10

EX10

1 Out of stock

Silver Round 10mm Essential Shamballa Fashion ...

MBJ01

2 £2.87

Blue Round 10mm Essential Shamballa Fashion Be...

MBJ07

2 £2.87

Some of the products required to make this item are either out of stock or no longer available.

Total Cost = £12.96
Add all products to basket

Step 1

Cut a 40cm piece of shamballa fashion cord. Measure around 10cm from one end and tie a knot. Put a safety pin through the knot and attach to a bead mat. Posititon so the long end points towards you, and the short end points away from you. Put a dab of nail varnish on the end of your thread to make threading beads easier. Now cut another piece of shamballa style cord approx. 1m in length. It is always better to overestimate the length to make sure you don't run out of cord! Find the centre of this cord and tie around your original cord, as close as you can to the pinned knot.

Useful tutorials for this step

Step 2

You now need to tie a square knot. Place the left thread over the centre thread & under the right thread, making a 4-shape. Now take the right thread & post the end underneath the point that the centre and left threads cross. Bring it up through the loop & pull both your outer threads away from each other to tighten. This creates half a square knot. To complete the square knot, do the same thing starting from the opposite side. So, take the right thread over the centre & under the left, creating a D-shape. Take the left thread under the point the middle & right threads cross, & bring up through the loop. Pull tight as before. Repeat this process until you have created approx. 3 square knots, then thread a bead onto the centre thread. Bring the outer threads around the bead and continue knotting. Add 1 or 2 square knots between each bead and keep going until you have added 7-9 beads. Tie 3 square knots after the last bead.

Step 3

 Cut off the outer threads leaving approx. 2mm either side. Glue the ends to hold your knotting. You can also singe the ends with a lighter, but take great care if you choose this option. Now turn your bracelet over. If you are adding a slider, thread either end of your centre thread through the slider in opposite directions. Take a new piece of cord approx. 1m long and tie over BOTH centre threads. Tie a few square knots before the slider, then bring the cords around the slider as you did with the beads earlier. Tie another few square knots after the slider, then secure the cord by glueing or singeing as before.

Step 4

Finally, thread a small bead onto each end to finish them off. Knot either end to keep the beads on. The knot with the slider should allow the two ends to slide through so you can make the bracelet larger and smaller. Find out how much you need to open the bracelet and make the ends just a little longer than this, then they won’t dangle too much when you are wearing the bracelet.

Get Your Materials!

Make sure you get the materials you need to create this design yourself! Click the button below to add everything you need to your basket in one go. You can edit the list too just in case you want to make more than one, or you already have some supplies at home. 

Get the items you need to make this