web analytics

‘Bordeaux’ WrapIt Loom Bracelet

The NEW WrapIt Loom by Rainbow Loom is here and we’re the first official U.K. suppliers of this awesome new tool! Making trending wrap bracelets has never been easier or faster with the WrapIt Loom. Inside the tool you’ll find a handy bead tray, lots of Toho seed beads with patterns and easy-to-follow instructions to make four different bracelets. Now that we’ve made all four bracelets in the kit, we’re using our own choice of beads to make a design of our own! I’ve chosen to use a rich mix of purple and burgundy glass beads inspired by Pantone’s autumn colour ‘Tawny Port’, with our sparkling new vintage pink glass faceted round beads in Pantone’s ‘Ballet Slipper‘ to lighten the design.

Project Materials

WrapIt Loom
Czech Fire Polished Glass Round Beads Amethyst 6mm Pk100
Preciosa Twin Hole Tile Square 6mm Frosted Amethyst Pk20
Preciosa Czech Fire Polished Beads 3mm Vintage Pink Pk100
Nymo Beading Thread Brown
Swarovski Heart Button Amethyst Pk1
Purple Waxed Cotton Cord 1mm 6 Metres
2x Beading Needles

Tutorial

Set up your WrapIt loom following the box instructions. Cut a length of purple cord approx. 34 inches long. Thread your button and move it to the centre of your cord. Take either side of the cords and tie a knot close to the back of the button. Roughly measure the length of the bracelet to your wrist and tie two LOOSE knots where you want the beads to end and the clasp to fit. Make sure you don’t pull the knot tight at this point so that you can easily adapt the length later on if you need to!

Now place the button and knotted end into the top clamp of your loom to hold it in place. Pass the opposite end through the clamp and wrap it around the WrapIt Loom end. Pull back the sliding part and press it into the groove to give you a tight tension.

  

Take a 1.5m length of cord and find the middle. Hold the middle point over your purple cords at the top of the loom. This is where you will begin to add beads. Take the left side of the thread and weave over the outside purple cord and back up through the middle between the two purple cords. On the opposite side do the same, taking the right thread around and up through the middle.

To add your first bead, take 1 vintage pink faceted bead and thread it onto one of the threads. Take the other thread and pass it through the bead in the opposite direction so that each cord crosses through it. Pull both of the threads until the bead sits neatly within the purple cords. After you add your beads, you will always pass each side of the thread back around the outside of the purple cords and up through the middle to complete the row. (Bear in mind that it will take a couple of rows for your design to sit nicely).

  

Next, thread on two pink beads and as before, pass the other cord in the opposite direction through the beads. Pull the cords and encourage the beads to sit within the purple cords. Bring each thread around the outside and up through the middle.

For the next set of rows complete the following:
1x 6mm bead.
2x pink 3mm beads.
1x tile bead – Since this is a twin hole, you need to treat it as if it were two rows of beads. Make sure you still wrap the threads around the outside of the cords before going through the second hole!

Repeat this pattern from your first two pink beads until you run out of room to add more beads. When you reach the end of the loom, check the bracelet against your wrist to see how much further length you wish to add. At this point, you can amend the knot if necessary. Place the bracelet further up the loom, gently clamping around the beads. Return the opposite knot to its position in the other clamp, pull back on the clamp and secure it down into the groove to give you your tension.

Continue to add your beads and when you are almost at the end, finish the design with two rows of pink beads, followed by a single pink bead to draw the end to a point. When you have finished adding beads, knot the thread a few times onto around the thread of a row and trim away the tail end.

You might like to secure the knots further with a drop of glue. Your bracelet is now ready to wear!

Previous Post Next Post

You Might Also Like

2 Comments

  • Reply Sarah Norell September 12, 2017 at 5:25 pm

    I’ve just completed this using 17 inches of cord. It barely makes it once around my wrist. Should the cord be doubled before cutting?

    • Katrina
      Reply Katrina September 13, 2017 at 11:24 am

      Hi Sarah, thank you for bringing this to our attention. This is a mistake on my behalf, I’m sorry! As you mentioned, I should have doubled this number to make it a double wrap bracelet. I have now amended the project. Please let me know if there is anything else I can do to help.
      Kind regards,

      Katrina

    Leave a Reply